On the afternoon of the fifth day, as soon as Chen Wen received the second version of the PCB with differential routing, he immediately had the surface-mount assembly plant expedite the processing.

The boards returned the following morning. He installed one onto the test engineering unit, and the Algorithm Group remotely ran a signal integrity test.

"The differential transmission is fine. Its anti-interference is better than single-ended."

The Algorithm Group Leader's voice came through the phone.

"However, after adding back the three-millimeter anti-vibration rubber pad at the base of the arm rod, the distance between the sensor and amplifier circuit changed, lengthening the signal path by four millimeters.

The gain stability is drifting a bit."

"How much drift?"

"It's fine at room temperature, fluctuating within 0.05 dB.

But after running the burn-in test for an hour, the board heated up to fifty-five degrees, and the gain drifted to 0.15 dB.

Although it's still within spec, mass-production consistency could run into some issues."

Chen Fan chimed in.

"If one board drifts by 0.15, there might be one out of a hundred that drifts over 0.3."

"Exactly.

When the time comes, the signal amplitude received by the annotation framework will fluctuate up and down, and the joint confidence will wobble with it."

Chen Wen removed the board from the test fixture and turned it over to check the impedance matching resistors of the differential routing.

There were two precision resistors with a nominal value of one hundred ohms, measuring 98.3 and 101.7 respectively.

"The impedance matching is off by three percent. High-frequency reflections might exacerbate the temperature drift."

"Can you replace them with higher-precision resistors on your end?"

"We have 0.1% tolerance ones, but the lead time is a bit..."

Before he could finish, Lao Zhao walked over briskly from the workshop floor, looking grim.

"Engineer Chen, about the reamers."

Hearing this, Chen Wen put down the board and asked,

"What happened this time?"

"The original supplier pushed back again.

They delayed it by another week."

Hearing that, Chen Wen fell silent for two seconds.

"How much do we have left in stock?"

"Out of the forty original manufacturer ones, eighteen are left. Out of the Kuncheng batch, twenty-two were used, leaving twenty-eight.

Based on tool changes every 5,500 operations, we consume about three to four a day.

In total, our inventory can only last ten to twelve days."

Ten to twelve days.

The original supplier's lead time had been extended by seven days.

There was already an eight-day shortfall, and combined, that made more than two weeks.

"Can we place an additional order with Kuncheng?"

"I asked.

The lead time for an additional order is nine days, and the unit price goes up another ten percent."

"Nine days and ten percent more."

Chen Wen calculated mentally and asked,

"What's the order quantity?"

"Minimum two hundred units."

Two hundred units, at the increased unit price, was nearly double the original supplier's price.

Yet this was currently the only way to bridge the gap.

Still, at least they had an alternative.

"Place the order.

Two hundred units, nine days.

At the same time, have Procurement keep pushing the original supplier. Every single day earlier counts."

Hearing this, Lao Zhao nodded and went to make the call.

Chen Wen returned to the second-version board and opened the procurement system to check the lead times for precision resistors.

For 0.1% tolerance SMD resistors, domestic brands had stock on hand, but their temperature coefficient was 25 ppm—still not good enough.

While the imported brand had a drift of 10 ppm, the lead time was three weeks.

Three weeks again.

He then picked up the phone and continued communicating with the Algorithm Group.

"The lead time for precision resistors is three weeks. Domestic stock is available, but the temperature drift is high.

Can software do temperature compensation for that 0.15 dB gain drift on your end?"

"How? Add a temperature sensor in firmware to calibrate gain in real time?"

"Yes.

The board already has an MCU, so we should be able to read temperature data."

"That's doable.

But it needs to be calibrated first.

Furthermore, we need empirical measurements for the gain drift curves across different temperatures.

Can you run a set of thermal chamber tests on your end?"

"No problem.

I'll have Lao Zhao run a batch first, from minus ten to seventy degrees, sampling every five degrees."

"Alright.

Give me the calibration data and I'll write the compensation algorithm.

That way we don't have to rush the precision resistors; we can make do with domestic parts and compensate via software."

"OK. Can the thermal chamber test start today?"

"I'll have Lao Zhao mount the samples right now."

Hanging up the phone, Chen Wen continued updating the whiteboard.

"Reamers: Original lead time +1 week, inventory sufficient for 10–12 days.

Added 200 units from Kuncheng, lead time 9 days, cost +10%.

Reamer shortage remains."

"Differential Board V2: Gain temp drift 0.15 dB @ 55°C, software temp compensation replacing precision resistors.

Thermal chamber calibration launches today."

...

After finishing the update, he took a step back to look at the entire whiteboard.

There were two more red circles now, especially around the reamer shortage issue, which was heavily circled in red ink.

The differential board temperature drift was marked in red as well.

Lao Zhao walked over from the thermal chamber and said,

"Engineer Chen, the thermal chamber is loaded.

Three boards running simultaneously, minus ten to seventy degrees, one data point every five degrees, stabilizing for thirty minutes at each temperature point before taking a reading."

"About how long to run the full cycle?"

"Sixteen hours."

"Works. We'll have data tonight."

"Alright.

Oh, right, there's an issue with the machining center.

After keeping the feed rate at 650, the yield rate stabilized around sixty-eight percent, but throughput can't ramp up.

At the current pace, monthly capacity tops out at eight hundred units—far short of the milestone for S02's initial batch of three thousand units."

Chen Wen rubbed the bridge of his nose.

Yield rate, production capacity, reamers, resistors, temperature drift, differential routing, and on and on.

For every one of these problems resolved, two more popped up.

"Keep the feed rate at 650 for now."

"A 68% yield rate is workable for now.

As for capacity, let's see if we can open an additional line first.

Can the second machining center be transferred over?"

"The second one is running rough machining for structural parts. Transferring it over means halting work on that end."

"Then halt it for now.

Outsource the rough machining of structural parts to a contract manufacturer, and transfer the machining center over dedicated to precision machining of joint modules."

"But if we outsource, the machining precision might be a bit..."

"It's fine. The tolerance requirements for rough machining are loose anyway; the contract shop can handle it.

As long as precision machining stays in our own hands, we'll be fine."

Hearing this, Lao Zhao immediately jotted it down and went off to arrange it.

Chen Wen sat back down in front of his computer and opened his email.

It was a message from the procurement manager.

"Engineer Chen, samples from the alternative driver board supplier can arrive next week, but the compatibility test results remain uncertain.

We're also pressing our previous supplier on lead times, but haven't received a definitive reply yet."

Reading this message, Chen Wen sighed.

A reamer shortage of over ten days, yield rate stuck at 68%, backup driver board undecided...

Why were there still so many issues?

Then, he opened his chat history with the Algorithm Group Leader.

The latest message was sent half an hour ago:

"The temperature compensation algorithm framework is written, awaiting calibration data.

Oh, right, we also ran a batch of complete data for joint verification using the new boards; the three-channel joint accuracy reached 95.2%.

The boundary confusion rate is 3.1%.

That's pretty good, but you need to hold steady on your end."

95.2%. 3.1%.

The algorithm track had gotten on schedule and was moving faster and faster.

Yet on the hardware side, there were still so many matters pending.

Chen Wen looked at the red circles on the whiteboard. After some thought, he picked up the red marker and drew an arrow after the reamer line pointing to 'Add 200 units from Kuncheng'.

Then he drew another arrow from the differential board temp drift pointing to'Software Compensation'.

He was clearly resolving problems non-stop, but why did it feel like the issues never diminished?

He let out another sigh, closed the email, and opened the thermal chamber monitoring software.

On the screen, three temperature curves were slowly climbing; between minus ten and zero degrees, the boards were entering the first test interval.

Lao Zhao shouted from outside,

"Engineer Chen, the contract shop called back. They can take on the rough machining, but the unit price went up fifteen percent."

"Acceptable."

"Alright."

Chen Wen didn't look up.

In the thermal chamber, the boards were still warming up; the machining center was spinning, the contract shop was taking orders, Kuncheng had the additional order placed, Procurement was pressing suppliers, and the Algorithm Group was waiting on data.

Chen Wen felt like every single day was like this now.

Moving one red circle a notch toward 'Observing', while watching two others turn deep crimson.

He stared blankly at the flickering numbers on the thermal chamber monitor until Lao Zhao walked over once more.

...